Tohnichi FTD Indicating Type Torque Screwdriver

Tohnichi FTD Indicating Type Torque Screwdriver

Features
Direct reading torque screwdriver ideal for inspection.
Features Pre-load Knob
Pre-load knob is designed to apply preliminary torque, which helps to reduce amount of turning and strain on the wrist.
Bi-directional scale plate
Available in SI, Metric or American units scales. Select model by unit and torque range required.
Metal Handle
Accepts 1/4" hex root bits. Includes 2 bits: plus and minus type.
Applicable for international use including the EU region. Compliant with calibration procedures of ISO 6789 Type I Class D.

Operating Procedure
Insert the bit into the bit holder.
Make sure FTD needle points Zero of FTD scale plate.
If the needle does not point Zero, it's required to adjust.
Start measuring or tightening operation.

Method of preloading FTD
The preload function is a thet uses the handle to apply a preloading torque close to that of the measuring point to minimize the twisting angle during measurement. In FTD torque driver, a preload function is provided to prevent your wrist from becoming difficult to read when operating close to the maximum torque.

1.Hold FTD with your left hand, turn the preload handle in the counterclockwise direction using the fingers of your right hand ( in case of clockwise measuring ).
2.After some slipping turns, the needle will begin to move, and it will be easy to set an optional torque value.
3.If you do not wish to use the preload function, turn the preload handle until there is no tension and the central set indicator ( red mark ) points to the FREE mark.

Warnings
Make sure there is no oil,or grease on the grip. A slip of the hand while tightening,may cause an accident or injury. Check for cracks,scratches and rust. These will cause damage to the driver and may result in an injury.If such conditions exist, have a functional test performed and repair if necessary.

Precautions
Don't use the torque driver beyond the maximum torque setting. This will cause damage or injury.
Don't use the torque driver if it is missing a pin or scale plate,etc. Ask a repair shop or our company to inspect the torque wrench and repair it before using.
Don't modify the torque driver. Modifications will weaken the torque driver. This may cause errors in accuracy,as well as,cause an accident or injury.
Don't drop the torque driver or apply a strong shock of jolt. This will cause damage or deformation as well as decrease the accuracy and durability,which may cause an accident or injury.
Use only parts designated by Tohnichi for repair of the torque driver. Ask the place of purchase or our campany for assistance when you repair,and use only Tohnichi parts.

Precautions for use
Confirm that the driver is set according to the correct unit of measure before using. (kgf􀉾cm, kgf􀉾m, N􀉾m, etc.)
Don't use torque driver in fresh water or sea water.
The inside mechanism will go bad and cause an accident or injury.If you drop in water or sea water,ger it checked out or repaired.
Use the correct bit that fits the screw,you are using.
Select the bit from the table for bits. Perform regular inspections for function and accuracy.
Periodical inspections are essential to insure the torque wrench is in optimal condition thus preventing injury.
Remove any dirt such as dust, mud, oil and water, etc. after each use and before storing torque drivers.
When storing the torque drivers for a long time, set at the minimum torque, and keep in a dry place.
If improperly stored,the accuracy and durability will decrease rapidly.
Note the following point when you attach or detach a bit or a socket.Hold the shaft as shown, when you attach or detach a bit or a socket.

We do undertake Servicing and repairing of Tohnichi FTD Indicating Type Torque Screwdriver TQC Sheen Range of products throughout india

Apart from supplying TQC Sheen Electrical Testing products in India through dealers network, catering to a variety of customers ranging from Atomic energy, Electricity Boards, Electrical Laboratory, Shopping Complexes, Shopping Mall, Electrical Contractors, Engineering Industries, Turnkey Construction Companies, Railways, Defence Installations, Research Laboratories, Educational Institutes and various Research and Development laboratories of leading national and multinational companies.

We DFT TECH, are TQC Sheen Authorized Distributors, Importers, Stockists, Dealers and Suppliers of Tohnichi FTD Indicating Type Torque Screwdriver Products in Chennai, Assam, Madurai, Coimbatore, Nagaland, Kerala, Manipur, Mizoram, Haryana, Sikkim, VIsakhapatnam, Tirchy, Hosur, Anjaw, Tumkur, Mysore, Kolkatta, Salem, Poonamalle and etc..