Lutron DT-2239A-1 Stroboscope (AC 110V power)
Lutron DT-2239A-1 Stroboscope (AC 110V power)
Lutron DT-2239A-1 Stroboscope (AC 110V power)
Description
The model DT-2239A is a microprocessor circuit design, high accuracy, digital readout, light duty STROBOSCOPE/TACHOMETER that is ideal for inspecting and measuring the speed of moving gears, fans, centrifuges, pumps, motors and other equipment used in general industrial maintenance, production, quality control, laboratories and as well as for schools and colleges for demonstrating strobe action.
Specification
Display :0.3" LED, 4 digits.
Stroboscopic Flash Rate :100 to 10,000 flashes per minute (FPM).
Accuracy :100 to 5,000 FPM/RPM) - ± 1 digit.
over 5000 FPM/RPM - ± 0.05% .
Resolution :Less than 10,000 FPM/RPM-1 FPM/RPM.
Over 10,000 FPM/RPM - 10FPM/RPM
Sampling Time :1 second.
Range Select :Automation.
Circuit :This stroboscope/tachometer employs an custom one-chip of microcomputer LSI circuit & crystal control time base which results in extraordinary accuracy over a wide, dynamic range.
Power Supply :110 Vac 10%, 50/60 Hz. or 220 Vac 10%, 50/60 Hz. or 230 Vac 10%, 50/60 Hz.
Power Consumption :Less than 30 Watt.
Operating Temp. :0 to 50 ℃ (32 to 122 ℉).
Operating Humidity :Less than 80% R.H.
Dimension :HWD - 21 x 12 x 12
Weight :1Kg/2.2 LB.
Housing :Compact and impact plastic injection case with plastic mirror type reflector.
Calibration :Crystal time base and microprocessor circuit, don't necessary take any external calibration process.
Accessories Included :Operation manual
Flash Tube Specification
Flash tube :Xenon lamp.
Flash Duration :Approximately 60 to 1,000 microseconds.
Flash color :Xenon white 6,500 K degree.
Flash energy :4 Watts-seconds (joules).
Beam Angle :80
Operating duty Cycle :For prolong life and safe operation, please adhere to the following duty cycle: Below 1,000 RPM - 30 Minutes. Above 3,600 RPM - 5 Minutes.
Always allow a 10 minute cooling off period between cycles.
Flash tube replacement :It is required to change the flash tube when the instrument start to flash irregularly at speeds of 3600 RPM/FPM or more.
Operation Procedure
Preparation :(a) Plug unit into a properly grounded 110V AC, 220V AC or 230V AC outlet.
(b) Turn the power switch to "on" position.
(c) Determine the range switch to "Low" or "High" position.
Checking Speed :When checking speed, care must be taken to insure that the strobe is flashing in unison (one to one) with the object being monitored. A Stroboscope will also stop motion at 2:1, 3:1, 4:1 et., this is normally referred to as harmonies. To be sure of unison, turn the dial until two images appear - this will double the actual speed. Then lower the flashing rate until a single and stationary image appears - this is the actual true speed.
Checking Motion :For motion analysis, simply locate the actual speed as mentioned above and then turn the dial slowly up or down. This will give a slow motion effect allowing complete inspection.
We do undertake Servicing and repairing of Lutron DT-2239A-1 Stroboscope (AC 110V power) lutron Range of products throughout india
Apart from supplying lutron Electrical Testing products in India through dealers network, catering to a variety of customers ranging from Atomic energy, Electricity Boards, Electrical Laboratory, Shopping Complexes, Shopping Mall, Electrical Contractors, Engineering Industries, Turnkey Construction Companies, Railways, Defence Installations, Research Laboratories, Educational Institutes and various Research and Development laboratories of leading national and multinational companies.
We DFT TECH, are lutron Authorized Distributors, Importers, Stockists, Dealers and Suppliers of Lutron DT-2239A-1 Stroboscope (AC 110V power) Products in Kerala, Goa, Himachal Pradesh, Ernakulam, Bangalore, Guntur, Pondycherry, Nagapattinam, Vandavasi, Kanpur, Lucknow, Rajapalayam, Sikkim, Ooty, Thrissur, Madurai, Jaipur and etc..
